Uvnc Pchelpware v2 RC1

[DennisvanderLinde]

Hi guys,
I'm new here and i dont know (yet) where to post this theath, so please move it to the right place

I have got a question, at the moment we are working on to get PChelpWare V2 RC1 running with the server and viewer.
http://www.uvnc.com/products/pchelpware ... -beta.html
The problem is that i have got an error while installing the server


I hope some one can help me with this, so i can go make a beginning of the server.

Btw,
Thank you very much for all the software we can download, its awesom!

Greetz,
Dennis van der Linde
Netherlands

[Rudi De Vos]

Did you exxperimented with the pchelpwarev2 server... normal you get this when the service is already installed and running.
The installer can handle this, when it was installed by the installer, but if pchelpwarev2 was installed manual for testing he can't correct it.
I had the same screen for this reason...cause, service fails already installed...

Try
net stop pchelpware_service
pchelpwareserver -uninstall
To make sure no "non msi" controled version is installed.

[DennisvanderLinde]

Dear Rudi,
I had it on my pc and laptop and the problem was that i had an SSD as main hard disk.
So, now i have installed it on normal harddisk without problems, but..
Now i want to connect to my dual-core server (where the server software is installed) and i try to connect to this server with te viewer.
When i do that i see that the server reacts inmideatly, but, it keeps "hanging" on initializing.
-Btw, thanks for the software, although it wont work here i will say it is really cool! Thanks

I will post 2 screenshots so you can see what my problem is!


So here you can see the server keeps hanging on initializing and wont go further. My viewer show this:
[imghttp://www.uploadplaatjes.nl/plaatje.php?id=340572][/img]
What you can see here is that i click on "Setup P2P" and the connection will be made.

So can anybody help me, i cant take over displays or send messages cause the connection keeps on initializing and will disconnect after about 20 seconds and i can start all over again, without any succes.

ByeBye
Dennis.

[DennisvanderLinde]

-edit
double post

[Rudi De Vos]

SSD: The developer pc used to make this sofwtare also has ssd's, it should not make a difference.
(The only problem i had with my ssd's is that the system crash if i activate in the powermanager that the disks can spindow...)

set password: did you set the same password before p2p
But this give a authentication error after +-20 seconds

modules are only visable after p2p is made.

Testing
1) Create a sfx on the viewer PC
2) Run this sfx on the same PC as the viewer and check if you can get the p2P up.
3) If this works, copy the sfx to a remote pc.

The sfx always extract in temp, you need to allow it in the firewall ( popup)
If the sfx is working, it should also work as service ( using the same config file)

[DennisvanderLinde]

Dear Rudi,
I think, seen by your name, you are dutch.
That would make talking lots easyer, cause i dont understeand totaly what i have to do now
Bye.

-update

I have made a LAN connection, cause externaly it wont work
What can i do,
With the viewer i can make a p2p connection to my server. But thats it, the 2 pc's in the viewer software are green
Now i press "modules", "RDP-Tcp#0 Active Maaswijk" and then "Open Deskop", "Chat" or "Send Message" but nothing happens, i click on it and just nothing happens.
What the hack is wrong? :O
Bye.

[DennisvanderLinde]

Any one guys? com on! need to get this software running asap