Cannot get SC to work at all.

[ncascais]

I am trying to set up SC to work only on my LAN.
I created the Helpdesk.txt file with my IP:5500, ZIPped it and created an EXE from that file. I set up VNCViewer in listen mode and I tried running the EXE file from another machine.
When I try running the EXE, it just unzips the files on the user's desktop and does not do anything else.
Re-did the whole process a few times with same result.
Any suggestions?
Thank you very much in advance,

Desperate user...

[bevtech]

These may help you in your quest of configuring single click

[topic=4606]UltraVNC SC STEP By STEP (Howto make a client EXE and setup)[/topic]

[topic=4530]UltraVNC SC manual SC EXE client (Client enters IP,PORT,ID)[/topic]

and if nothing else you can try this vnc-related product
[topic=7324]SCWIZ (Wizard) easy setup.[/topic]

[ncascais]

Do I still need to make changes on my router if I this will only work on the LAN?

[redge]

No

[ncascais]

I must be doing something wrong...
I think the problem lies on the .exe file the user downloads.
The only thing that happens when the user run the executable is that the 6 files in it are copied to the desktop, it does not trigger the connection.
Any ideas?
Thank you in advance.

[bevtech]

what do you mean??

I must be doing something wrong...
I think the problem lies on the .exe file the user downloads.
The only thing that happens when the user run the executable is that the 6 files in it are copied to the desktop, it does not trigger the connection.
Any ideas?

How are you compiling this .exe??

What is in your helpdesk.txt with the a fake ip please??

you seem to have something majorly wrong..

[ncascais]

This is my Helpdesk.txt. I have my internal IP address.

Code: Select all

[TITLE]
           UltraVnc SC

[HOST]
Internet support
-connect 192.168.100.246:5500 -noregistry

[HOST]
Internet support encryption
-plugin -connect 192.168.100.246:5500 -noregistry

[TEXTTOP]
Dubble Click to make a connection

[TEXTMIDDLE]
Before making a connection

[TEXTBOTTOM]
Please Call 973 344 4570 if you need further assistance

[TEXTRBOTTOM]


[TEXTRMIDDLE]
Metal Management NE, Inc

[TEXTRTOP]
Ultravnc PC support

[TEXTBUTTON]
Company Webpage

[WEBPAGE]
http://www.mtlm.com

[TEXTCLOSEBUTTON]
STOP test


[BALLOON1TITLE]
Establishing connection ...

[BALLOON1A]
5 min try period

[BALLOON1B]
If it fails, the software will remove himself

[BALLOON1C]
from your system. 

[BALLOON2TITLE]
Connection active.

[BALLOON2A]
Warning, your desktop is remote visable

[BALLOON2B]
You can break the connection any time

[BALLOON2C]
by using the close button

[WEBPAGE]
http://www.ultravnc.net

[/code]

[Suntzu]

Something that sometimes works is making sure that the port is forwarded and if there is a checkmark "enable" next to the port, make sure it's checked and make sure only one is enabled also make sure your IP has not changed, you can check by going to cmd and typing in ipconfig.

[Suntzu]

I am trying to set up SC to work only on my LAN.
I created the Helpdesk.txt file with my IP:5500, ZIPped it and created an EXE from that file. I set up VNCViewer in listen mode and I tried running the EXE file from another machine.
When I try running the EXE, it just unzips the files on the user's desktop and does not do anything else.
Re-did the whole process a few times with same result.
Any suggestions?
Thank you very much in advance,

Desperate user...

How are you creating the .exe file? You should use the VNC SC uploader.